What does no MDIX auto mean?
Switches and hubs not having Auto-MDIX will typically have one port that will not cross the line or crossover. MDIX is a version of the medium dependent interface (MDI), which is a module of the media attachment unit (MAU).
What is Auto MDIX feature on a switch?
Automatic medium-dependent interface crossover (Auto-MDIX) is a feature that allows the switch interface to detect the required cable connection type (straight-through or crossover) and automatically configure the connection appropriately.
How do I check MDIX?
To check cable you have to look at connectors at both ends and see if two wires are crossed. A regular cable both ends will have wires that look flat. A cross-over cable one end you will see two wires that are not flat. You will never see a cable with cross-over on both ends.
What is Auto MDIX CCNA?
a feature that detects Ethernet cable type. Explanation:Auto-MDIX is a feature that is enabled on the latest Cisco switches and that allows the switch to detect and use whatever type of cable is attached to a specific port.
What is the Auto MDIX feature on a switch quizlet?
What is the auto-MDIX feature? – It enables a device to automatically configure an interface to use a straight-through or a crossover cable.
What is the difference between MDI and MDIX?
MDI/MDIX is a type of Ethernet port connection using twisted pair cabling. The standard wiring for end stations is MDI, whereas the standard wiring for hubs and switches is MDIX.
How do I turn on auto MDIX?
Auto MDIX is turned on by default. To disable Auto MDIX on a port, use the no mdix auto command under the interface configuration mode. To put it back to default, use the mdix auto command in the interface configuration mode.
Which switching method makes use of the FCS value?
CCNA 2 Chapter 2 Switching Concepts
| Question | Answer |
|---|---|
| Which switching method makes use of the FCS value? | Store and forward |
| Which switch characteristic helps alleviate network congestion when a 10 Gbps port is forwarding data to a 1 Gbps port? | Frame buffering |
What command verify Mdix?
Monitoring Auto-MDIX
| Command | Purpose |
|---|---|
| show controllers ethernet-controllerinterface-id phy | Verifies the operational state of the auto-MDIX feature on the interface. |
What is the Auto-MDIX picture?
It enables a device to automatically configure an interface to use a straight-through or a crossover cable. It enables a device to automatically configure the speed of its interface. …
What are two actions performed by a Cisco switch?
What are two actions performed by a Cisco switch? (Choose two.)
- building a routing table that is based on the first IP address in the frame header.
- using the source MAC addresses of frames to build and maintain a MAC address table.
- forwarding frames with unknown destination IP addresses to the default gateway.
What are two methods for switching data between ports on a switch choose two?
There are 2 methods that all switch use for forwarding the frames (switching data) between the network ports:
- Store and forward switching.
- Cut-through switching.
How does auto MDIX work on Cisco switch?
When auto-MDIX is enabled, the interface automatically detects the required cable connection type (straight-through or crossover) and configures the connection appropriately.
What kind of cable do I need for auto MDIX?
Therefore, you can use either a crossover or a straight-through cable for connections to a copper 10/100, 10/100/1000, or 1000BASE-T SFP module port on the switch, regardless of the type of device on the other end of the connection. The Auto-MDIX feature is enabled by default on switches running Cisco IOS Release 12.2 (18)SE or later.
Is there auto MDIX on Cisco Catalyst 2950?
Note: The auto-MDIX feature is enabled by default on Catalyst 2960 and Catalyst 3560 switches, but is not available on the older Catalyst 2950 and Catalyst 3550 switches. To examine the auto-MDIX setting for a specific interface, use the show controllers ethernet-controller command with the phy keyword.
What do you need to know about auto MDIX?
When connecting to switches without the auto-MDIX feature, straight-through cables must be used to connect to devices such as servers, workstations, or routers and crossover cables must be used to connect to other switches or repeaters.